VARGLINK

Stark Varg FAQ

Answers from owners' experience in the Russian-speaking Stark Varg chat: charging, firmware, suspension, maintenance, buying. Translated from Russian.

What are the differences between Stark Varg models (MX gen1/gen2, MX 1.2, EX, SM)?

The difference is the model, not the year.

  • MX 1 (2023–25, gen1/gen2) — 6.5 kWh battery, the first model.
  • EX (2025+) — 7.2 kWh, new wiring, frame, phone, enduro suspension and fork angle, headlight, brake light.
  • MX 1.2 (2025+) — 7.2 kWh, new wiring, frame, phone, revised MX suspension.
  • SM (2026+) — new wiring, frame, phone, SM suspension, fork angle, triple clamp, headlight, brake light.

Plastics and wheels are the same on all models; among the brakes only the front one on the SM differs. Motors and gearboxes are identical. Gen1 and gen2 barely differ: the charging port was moved and the wiring rerouted.

from the Stark Varg chat · 10.08.2026, 22.10.2024 · separate page
What are the torque specs on the Stark?

From the EX and MX 1.2 manuals (N·m)

Front end and handlebar

  • front axle (lock bolt) — 35, axle clamps — 15
  • front caliper — 25
  • phone dock (holds the handlebar) — 30
  • hand brake master cylinder, clamp — 6
  • throttle — 2.5, throttle clip — 3, control switch — 2.5
  • brake hose holder on the fork — 5, front fender — 8, number plate — 5

Frame and rear suspension

  • swingarm (pivot) — 45, swingarm pivot pinch bolt — 25
  • shock, top and bottom — 40
  • pull rods — 60
  • rocker: reverse nut — 20, main pivot — 60, lock nut — 60, pivot caps — 5
  • side panels — top 20, bottom 30
  • footpeg pin — 20, skid plate — 15
  • side stand: bracket — 20, leg — 35
  • VCU: side bolts — 2, center bolts — 55

Rear and brakes

  • rear axle — 80
  • rear sprocket bolts — 35
  • brake disc bolts — 14
  • foot brake master cylinder — 10, pedal pivot — 5
  • chain slider — 5

Spoiler: rear center — 10, sides — 20, front — 5, carbon — 3.

Titanium fasteners use the same values and are checked after every ride.

From owners' experience: triple clamps — bottom 13–14, top 17; handlebar — 30. Gearbox: drain bolt 15, check bolt 5, filler plug 5. Kayaba fork: cartridge cap 29, bottom bolt 55, oil per leg 328 ml (295–370).

Engraving on the triple clamps (no torque for the clamps was found in official Stark documents): bottom — 17, top — 20, handlebar clamp on the top one — 25. The chat's consensus is 15 for the bottom clamp; whether to follow the engraving for the top clamp and bar clamp is still debated.

from the Stark Varg chat · 20.04.2026, 21.10.2026 · separate page
How do I tell the suspension spring rate from the marking?

The letter is stamped on the left fork leg (at the bottom, on the axle foot) and on the shock spring carrier. Weight is with riding gear.

EX

  • fork: H 4.4 · J 4.6 · K 4.8 N/mm
  • shock: H 46 · J 48 · K 50 N/mm
  • H — 65–75 kg, J — 75–90 kg, K — 90–100 kg

MX

  • fork: E 4.6 · F 4.8 · G 5.0 N/mm
  • shock: B 54 · C 56 · D 58 N/mm
  • E/B — 65–75 kg (soft), F/C — 75–85 kg (medium), G/D — 85–100 kg (hard)
from the Stark Varg chat · 19.07.2025 · separate page
What are the stock suspension clicker settings, and what to run for enduro?

Stock EX (clicks out from fully closed)

  • fork: compression 13, rebound 10
  • shock: compression HS 14, LS 14; rebound LS 12, rebound 10

Enduro setup from the chat's pinned messages (from closed)

  • front: compression 20, rebound 18
  • rear: compression L 20, H 20; rebound L 15, H 15

For motocross the pinned messages have Casey Casper's table (second column).

from the Stark Varg chat · 19.05.2025, 07.07.2024, 10.02.2025 · separate page
How should I charge the battery and balance the cells?

Slow charging is better (0.3–1 kW); use fast 3.3 kW when you need it at a race.

Balancing happens around 80% and while the bike sits after a full charge, so now and then leave it on the charger overnight or for a day. A working routine from the chat: keep it at 80%, and the night before a ride charge to 100% at 0.3 kW.

Cell difference

  • up to ~0.010 V — normal
  • 0.02 V — acceptable
  • 0.05 V and above — needs balancing (24 hours at 0.5 kW brought 0.087 → 0.007 V)
from the Stark Varg chat · 29.10.2025, 27.08.2025, 26.10.2025 · separate page
How do I extend battery life?
  • don't run it down to zero
  • don't use full throttle at low charge (below ~10–20%)
  • don't charge below +4 °C (per the manual)
  • store at 30–50%
  • occasionally charge slowly to 100% for balancing
  • charge to 100% right before a ride, don't keep it there for weeks
from the Stark Varg chat · 02.07.2025 · separate page
The bike shut off at low charge under full throttle / won't turn on after being run to zero — what to do?

Below ~10% at full throttle the Stark goes into protection to save the controllers. The battery is not dying.

Forced start

  1. Remove the spoiler and the carbon cover.
  2. Press the power button three times for 2 s until the red light goes out.
  3. Within 5 s, disconnect the orange HV connector and wait 5 s.
  4. Hold the power button (red lights up) and within 2 s reconnect the HV.

It may take several attempts; don't do more than 10 — contact Stark support.

On newer MX firmware, starting from a full shutdown needs 4.4–4.5 V on the VCU battery, otherwise it blinks red three times.

from the Stark Varg chat · 05.03.2025, 20.01.2025, 07.04.2026 · separate page
How do I fully switch the bike off, and why does it drain while parked?

Blinking red is sleep mode; it uses about 1.5–2% per day (phone and connectivity).

Full shutdown: hold both white map buttons (+ and −) until it blinks white.

If you leave it for several days or longer, shut it down fully.

Stark videos: switching off — https://youtu.be/PWP1QAd6Mcw, full shutdown — https://youtu.be/3iA8mMst4mw

from the Stark Varg chat · 18.04.2024, 24.09.2025 · separate page
How do I store the Stark in winter, and can I ride in freezing weather?

Per the manual

  • store at 0…+30 °C, ideally around +10 °C, dry and frost-free
  • battery charge 30–50%; before storage run it down to 30% and charge to 50% — this balances the cells
  • check the charge every two weeks; if it drops below 30%, top up to 50%; never let it run flat
  • don't charge below +4 °C
  • recommended operating range is 0…+25 °C

From the chat: a fully switched-off bike kept warm loses about 5% over winter. You can ride below zero, but with a warm battery from a warm garage and without charging in the cold; range is lower in the cold.

from the Stark Varg chat · 01.10.2026 · separate page
Why does the app allow only 2 kW charging instead of 3.3?

Common after moving the slider or updating the app: settings are pulled from Stark's server.

Rotating the phone between portrait and landscape and updating the app helped; later many got up to 6.6 kW without updating the bike. Most people still charge at 1–1.5 kW.

from the Stark Varg chat · 29.01.2026 · separate page
What generator can charge a Stark?

You need an inverter generator — a regular one barely charges.

  • Hyundai 3.3 kW holds a 3 kW load for 1.5–2 hours, charging about 1% per minute
  • TSS 3 kW — a bit slower than 1%/min, but lighter

The charger is set to 1.8–3 kW.

from the Stark Varg chat · 20.04.2026, 20.01.2025 · separate page
The charger doesn't charge or shuts off — what's the cause?

What came up in the chat:

  • the magnetic connector inside the charger came loose — open it and check
  • overheating in hot weather — protection switches it off, half an hour later it works again
  • if the bike charges with someone else's charger, the charger is faulty: repair or replace (the compact one costs the same as the big one)

The stock charger is waterproof with the cover closed.

from the Stark Varg chat · 20.04.2025, 20.11.2025, 06.09.2026 · separate page
How long does the battery last?

It depends heavily on power setting and riding style.

  • Hard enduro: 45 km and 80% over 3.5 engine hours; 2.5 hours of slow technical crawling — 5 km and 35% used
  • Easy trail riding: an EX covers up to ~80 km
  • Motocross at full throttle: from 40 minutes to 1.5 hours
  • Per the manual: up to 6 hours of riding, full charge about 2 hours from 220 V
  • Rule of thumb from the pinned messages: MX ~30 km, EX at the same pace ~40 km

Save energy with power settings (30–45 hp), regen and gearing.

from the Stark Varg chat · 01.12.2025, 07.03.2026, 13.11.2025 · separate page
How do I update the bike's firmware?

The bike's modem needs stable mobile internet (4G, not Wi-Fi). Usually the update arrives while charging or after a ride with good reception.

Per the manual: switch the bike on (On/Off button for 2 s). If the LED is magenta, the update is ready: hold + and − for 5 seconds. The chat advises holding up to ~12 seconds if it doesn't start the first time.

If it doesn't arrive

  • fully shut down with the two buttons and switch on again
  • write to Stark support with your VIN — they push the update
  • check the modem and the SIM

Since app version 3.4.1 the update can be received via the Stark phone, without a modem connection.

The app version on the phone and the bike firmware are different numbers.

Stark video: https://youtu.be/LiSrJl6rhaI

from the Stark Varg chat · 04.10.2026, 19.10.2026 · separate page
How do I register and transfer the bike to my name (Stark account)?
  • Register at starkfuture.com; a Gmail address works.
  • The app login and password are the same as on the website.
  • The previous owner or the seller must transfer the bike from their account to yours. If they drag their feet, Stark support can help.
from the Stark Varg chat · 17.04.2026, 18.01.2025, 26.03.2025 · separate page
How does the Stark warranty work?

Per the manual: the warranty is 2 years from handover to the buyer. Parts replaced under warranty don't extend it.

Not covered: skipping the maintenance schedule from the manual (missing scheduled service voids the warranty), non-original parts and modifications, repairs by unauthorized persons, crashes and accidents, normal wear, participation in official competitions, rental and commercial use, submersion.

How to file a claim: email [email protected] with your full name, address, phone, model, VIN, purchase date, a description of the problem and photos. They may ask for proof of maintenance — dates and receipts for parts and fluids — so keep them.

From the chat's experience: they often ask for a video. Low-voltage parts are replaced without trouble; the power components (battery, motor) take long and are harder. The warranty can be extended for a fee on the website.

Once the warranty has expired, it can't be renewed or extended.

from the Stark Varg chat · 05.02.2026, 27.03.2026, 22.10.2026 · separate page
What gearbox oil, how much, and how often to change it?
  • Oil: 75W-90 gear oil (or 80W-90)
  • Volume: about 80 ml — up to the check bolt
  • Interval: per the manual every 40 hours, first change at about 5 hours

If you ride through water and the breather isn't raised, change it more often — water emulsion happens.

Torques: drain bolt 15 N·m, check bolt and filler plug 5 N·m.

Stark videos: MX 1.2 — https://youtu.be/MzsXAV4Ee1E, MX — https://youtu.be/24lAXWuuTGI

from the Stark Varg chat · 23.03.2026, 10.06.2026 · separate page
What coolant to use, and why does the fan run so often?

Overheating is almost always caused by air in the cooling system — it has to be bled properly.

People use G12+ or their own mixes. The pinned messages suggest water/concentrate 5:1 with Water Wetter additive (freezes at −8 °C): with it the fan comes on noticeably less often.

In the woods in hot weather the fan may run constantly — that's normal.

Stark videos: bleeding the cooling system, MX 1.2 — https://youtu.be/iItNWwhdmEQ, MX — https://youtu.be/dZMHxFu8dU4

from the Stark Varg chat · 04.02.2025, 27.05.2025, 04.06.2026 · separate page
Pump error or "fan overheating" — what to do?

Don't ignore pump messages: stop and restart, otherwise the bike may cut out while riding.

Common causes:

  • dirt or moisture in the fan — wash, blow out, check that it spins
  • the pump itself — new ones are sold by parts dealers

The fan impeller isn't serviced separately — the whole fan is replaced.

from the Stark Varg chat · 31.05.2025, 31.03.2025, 15.04.2026 · separate page
The bike shuts off while riding or shows a red light — where to look?

Most often, according to the chat:

  • poor connector contact — plugs under the phone holder and dash, the connector on the right under the plastic, connectors on the EX: press in, reconnect
  • firmware — for many the problem went away after an update
  • stuck or shorted buttons and the brake light switch

In difficult cases Stark support diagnoses remotely (motor position sensors and motors have been replaced under warranty).

from the Stark Varg chat · 16.08.2025, 20.08.2026 · separate page
The bike is stuck in crawl (turtle) mode or reverse — what to do?

Check the button on the control switch: moisture or oxidized contacts make the mode stick. Sticky buttons were fixed by taking them apart and lightly cleaning the inside with fine sandpaper.

It doesn't mean Stark has locked the bike.

from the Stark Varg chat · 17.06.2026, 06.04.2026 · separate page
The throttle doesn't respond — what to check?
  • whether the bike lock is enabled in the app
  • the plug under the dash (phone holder)

A red LED at power-on is one of the signs of a faulty throttle.

The throttle is electronic and breaks in crashes — many turn it downward and fit handguards or bar-end plugs.

from the Stark Varg chat · 19.10.2026, 09.05.2026, 13.11.2024 · separate page
What alternative apps are there for the Stark?

First place goes to VargLink: according to users, it works better than the other unofficial apps.

  • VargLink — charging control, including remote, and fault diagnostics (the bike's error log): https://varg.aupov.tech
  • VargPilot — a replacement for the stock app: telemetry, HUD, logging
  • starkvibe.ru — themes for VargPilot, the Stark Map and a VargPilot ↔ Stark switcher without reinstalling
  • FENR — an iPhone app (App Store "FENR – Unleash your varg")
  • SVAG — telemetry and balancing (TestFlight and Google Play links in the pinned messages)
  • there is a separate app for WearOS watches by a chat member
from the Stark Varg chat · 10.09.2026, 19.09.2026, 20.10.2026 · separate page
Will VargPilot void the warranty, and is there a risk of bricking?

The stock app is disabled via a website (starkvibe.ru has a switcher). There is a risk something goes wrong, but by the chat's experience it's already very small.

VargPilot cuts the connection to Stark's server, so for warranty claims many switch back to the stock app.

from the Stark Varg chat · 18.09.2026, 14.06.2026 · separate page
The Stark phone got drowned or broke — what to do?
  • Original phone — ask the parts sellers (@BackJumpMoto, @WRracer).
  • On an older MX — buy a similar device (Blackview 6300 Pro) and transfer the dump from a working Stark phone. There is an example of this in the chat's pinned messages.

Important: the regular Blackview 6300 (non-Pro) does not work for the MX — it has no wireless charging. Wireless charging is only on the 6300 Pro.

Stark videos: removing and installing the phone: MX 1.2 (Arkenstone) — https://youtu.be/ZPb7d-8MR3o, MX — https://youtu.be/k9ScGrnVjWM

from the Stark Varg chat · 29.07.2026, 25.10.2026 · separate page
Do I need a subscription for the maps (power modes) to work?

No, the mode maps work without a subscription. The subscription is needed for throttle and brake curves (TC Braking); VargPilot gives the same.

If the maps don't show, switch the dashboard view to the map.

from the Stark Varg chat · 29.03.2026, 16.09.2026, 05.09.2026 · separate page
What map settings (power, regen, traction) for hard enduro?

Owners' examples:

  • main — 45 hp, regen 0–40%, no TC
  • wet and loose off-camber, long descents — 30 hp, regen 70–100%, TC 80–100%
  • climbs — the "sweet spot" of 55 hp and 40% traction
  • pushing the bike — 10–15 hp, regen 100%

There's no point going below 30–35 hp except for pushing.

from the Stark Varg chat · 02.10.2026, 05.11.2024 · separate page
Do I need regen, and how much?

It's a matter of taste.

  • Motocross: many run 0–30%. With strong regen the front dives when you close the throttle, and in the wet the rear wheel can try to overtake the front.
  • Woods and descents: regen helps engine-brake and adds a little charge (a long descent gave back 4%).
  • Long races: from 20% is recommended to save energy.
from the Stark Varg chat · 01.12.2024, 10.09.2026, 16.03.2025 · separate page
How do I hold the bike on a slope — is there hill hold?

Only crawl mode holds the bike with the motor — that's the hill hold, but it uses battery.

Otherwise hold it with the throttle or brake; you can fit a parking lock on the front and rear brakes.

from the Stark Varg chat · 30.11.2025 · separate page
The rear or front brake is weak. What should I do?
  1. Replace the brake fluid.
  2. Bleed the brakes: if the lever pulls all the way to the bar, there is air in the system. It helps to lay the bike on its left side and pump the lever about 15 times.
  3. Fit a spring steel disc.
  4. If the brake got weak after mud or a bog: ride in reverse and squeeze the brake a couple of times. Sometimes this cleans the brake.

For the rear, people also fit a 9 mm clutch master cylinder and Polisport levers.

Stark video: MX 1.2 rear caliper maintenance — https://youtu.be/WPdC1iC7LbQ

from the Stark Varg chat · 23.03.2026, 28.09.2026, 28.10.2026 · separate page
Which brake pads fit?

The same as KTM: original, Brembo, and other KTM-fit pads.

  • rear — TRW MCB743SI
  • front — TRW MCB648SI
from the Stark Varg chat · 29.03.2026 · separate page
Which brake levers fit?
  • Front (right) — KTM 1:1, Polisport for Brembo.
  • Left hand rear brake — Polisport, or a Braktec clutch lever (HQV/GasGas) with light filing; Braktec doesn't fit the stock Brembo.
  • There are cheap marketplace levers (need filing) and 3D-printed "unbreakable" ones.
from the Stark Varg chat · 16.09.2025, 22.09.2025, 07.09.2026 · separate page
Can I run both a foot and a hand rear brake?

Yes: ready-made kits exist — a cylinder screws in instead of the plug, with a banjo to the hand master cylinder.

A twin-piston rear caliper is fitted with a milled adapter bracket (with or without a disc guard).

from the Stark Varg chat · 27.09.2026, 26.09.2026 · separate page
The suspension is very stiff — what to do?
  1. Check that the springs match your weight in gear (see the marking). If not, clickers won't help — change the springs. A working setup from the chat: Öhlins on the shock, WP or Yamaha on the fork.
  2. Set the SAG (~110 mm in gear).
  3. Service the suspension: the factory oil is "strange" and the shock is sometimes not vacuum-filled. On a new bike a service is advised after 5–30 hours.

Suspension tuners are recommended in the Stark Varg chat.

from the Stark Varg chat · 05.07.2025, 26.10.2025, 01.10.2026 · separate page
How do I set the rear shock SAG?

SAG is measured from the rear axle to the SAG mark on the rear fender, on level ground, with the rider sitting in the middle. Three positions:

  • A — unloaded, rear wheel off the ground
  • B — bike on its wheels under its own weight
  • C — rider in full gear on the bike

Targets

  • A − B (static sag) = 40–45 mm
  • A − C (race sag) = 102–108 mm

These are the old MX manual values. In the EX and MX 1.2 manuals: A − B = 40 ± 3 mm, A − C = 110 ± 3 mm.

Race sag is set with spring preload: loosen the lock ring and turn the spring itself by hand. If it's tight, lift the wheel or spray some WD-40.

If static sag isn't 40–45 mm with correct race sag, the spring doesn't match your weight.

from the Stark Varg chat · 19.10.2026, 25.09.2026 · separate page
The handlebar points sideways after a crash — how to straighten it?

After crashes, loosen the fork leg bolts in the triple clamps, shake the fork so it settles, and retighten — a must-do procedure. The bar mounts sit on rubber dampers and can end up crooked.

Torques: triple clamps 13–14 N·m bottom and 17 top, handlebar 30 N·m.

from the Stark Varg chat · 02.08.2025, 01.08.2025 · separate page
What sprockets are stock, and what to run?

Stock: EX — 12/48, MX — 14/47.

  • 12/48–12/52 — popular for hard enduro: lower current and heat, more economical in slow technical riding
  • 13/47 — faster
  • 12/52 — for crawling, loses on fast sections

Sprockets are bought from Mayak Lab (KTM ones fit too). Minimum rear is 43 teeth; below that the teeth hit the bolts.

from the Stark Varg chat · 03.10.2026, 15.03.2026 · separate page
How do I adjust chain tension?

Target: 45 mm, for sand — 50 mm. Measure from the swingarm to the chain right behind the slider, bike on a stand. Less than that and the chain goes tight as a string when the swingarm compresses; from the factory the chain is sometimes too tight.

Don't confuse this with 25–32 mm — that's the slack of the chain itself, not the distance from the swingarm.

Mayak Lab makes a chain tension gauge for the Stark.

How to adjust: loosen the rear axle (torque 80 N·m) — you can't adjust without it, set it with the adjusters, tighten the axle.

The chain slider on the swingarm is usually a KTM one with an adapter.

Stark video: removing and installing the chain, MX 1.2 — https://youtu.be/tQw_BhAxjc4

from the Stark Varg chat · 19.10.2026, 17.03.2025, 13.06.2026 · separate page
How do I undo the front sprocket nut?

Engage crawl mode or reverse and undo it with an impact wrench. Without one, brace a ratchet against the footpeg and give it a gentle bit of throttle — the Stark will undo it itself.

Usually you'd hold the rear wheel so the chain doesn't turn.

Stark video: replacing the front sprocket, MX 1.2 — https://youtu.be/m_4MPSopNKg

from the Stark Varg chat · 18.07.2026 · separate page
Do KTM wheels fit?
  • Front — fits as is, with KTM spacers.
  • Rear from a TPI — swap the seals and spacers.
  • Rear from a TBI — the spacer sleeve must be replaced (25 mm axle).
  • With a KTM 2026 wheel the spacers were changed.

Stark videos: removing and installing the rear wheel, MX 1.2 — https://youtu.be/pcqAfkvK998, front — https://youtu.be/GLvPtIIWlus

from the Stark Varg chat · 04.08.2026, 24.03.2026 · separate page
What tubes come from the factory, and what to fit?

Factory tubes are thin — many replace them after the first rides.

People fit heavy-duty tubes (4–6 mm, Mitas, HD), Tubliss, Tubliss-mousse or a mousse; many also run Tubliss or mousse up front.

  • With a mousse you need a rim lock (one is enough), otherwise the tire spins on the rim.
  • Hard enduro pressure with Tubliss — about 0.2–0.3 bar.

Mousse per the manual: lubricate with mousse gel at least every 5 hours of riding, no faster than 130 km/h, off-road only, rim lock recommended; store at +5…+30 °C in a box, away from sunlight.

from the Stark Varg chat · 11.12.2024, 22.04.2026 · separate page
What wheel bearings are used?

Almost all bearings are the same as the KTM SX-F 2022, except the front wheel — it uses the same as the rear, 6005.

from the Stark Varg chat · 19.11.2024 · separate page
What protection and upgrades do people fit right after buying?
  • motor and gearbox cover guards — Mayak Lab, NICECNC, carbon or 3D-printed from the file in the pinned messages
  • linkage guard
  • handguards or bar-end plugs — the throttle is electronic and breaks in crashes
  • a long seat cover with grip — the stock one is slippery
  • a convenient box for the charger

The chain guide on the EX doesn't need replacing — it's thicker there.

from the Stark Varg chat · 26.06.2025 · separate page
The lower plastic tray and foam are falling apart — what to do?

A common problem: the tray plastic splits and the mounts in the foam tear out.

People fit a new tray and foam plus a skid plate (HardGlide, carbon). Lost threaded inserts in the plastic are glued or melted back in.

from the Stark Varg chat · 30.09.2025, 20.11.2025 · separate page
Which bar-end plugs fit?

Inner handlebar diameter:

  • on newer Starks — 13 mm
  • on older ones (e.g. MX 1.0) — 14 mm

Regular KTM plugs fit a 14 mm bar. For 13 mm, drill the hole out or use plugs from trial bikes.

from the Stark Varg chat · 19.10.2026, 23.09.2025, 19.11.2025 · separate page
Should I get a Stark instead of a gas enduro bike, and what to expect?

Opinions differ: many sold their gas bikes and ride only the Stark, others keep an ICE bike as a backup.

What to expect:

  • waiting for warranty parts — weeks to months
  • the modem + SIM + updates combination
  • the Stark is heavier than a gas bike

Coming from a 250 cc, it's advised to start at 60 hp, not 80.

from the Stark Varg chat · 04.11.2025 · separate page
What to check when buying a used Stark?
  • a battery status screenshot — cell difference and capacity are what matter most
  • error history
  • whether the modem connects and the firmware is up to date
  • whether the seller will transfer the bike to your Stark account
  • engine hours in the app can be off
from the Stark Varg chat · 24.01.2026, 14.09.2026 · separate page
How much does a Stark weigh, and is it hard to pick up?

An EX with carbon guards, handguards, Tubliss and a bag weighs about 126 kg on the scales.

The load on the bar when lifting is a bit higher than a KTM 300 TBI, though many find the difference significant. A 60 kg rider can ride it, but hauling it around is hard.

from the Stark Varg chat · 09.05.2026, 13.07.2025 · separate page
How should I transport the bike?
  • Per the manual: on a level trailer, with straps around the fork legs above the bottom triple clamp on both sides. Don't lift the bike with lifting gear — only roll it on its wheels.
  • From the chat: it can also lie on its side in a trailer.
  • Under a cover on the road the wind rubs the decals — use a cover only for storage.
  • In winter on an open trailer road salt quickly causes rust — a covered trailer is better.
from the Stark Varg chat · 26.09.2026 · separate page
Stark Varg specs: EX, MX 1.2 and the first MX

EX (enduro)

  • power 44 kW (Standard, 60 hp) / 60 kW (Alpha, 80 hp), motor torque 70 / 90 N·m
  • battery 7.2 kWh, 420 V
  • weight 120 kg (race configuration), top speed 129 km/h per the manual (in reality around 135, sprockets 12/48)
  • tires 90/90-21 and 140/80-18

MX 1.2 (motocross)

  • same power, torque and battery
  • weight 118 kg, top speed 154 km/h per the manual (in reality around 160–165, sprockets 14/47)
  • tires 90/90-21 and 140/80-18

MX (the first one, gen1/gen2)

  • 44.7 / 59.7 kW, torque 60 / 80 N·m
  • battery 6.48 kWh, 420 V
  • weight 118 kg, top speed 110 km/h per the manual (in reality around 160)

General: up to 6 hours of riding, charging takes about 2 hours from 220 V, service life per the manual is 500 engine hours, max RPM 13,900 (14,200 on the first MX). Suspension by rider weight: Soft 65–75, Medium 75–90, Hard 90–100 kg.

from the Stark Varg chat · separate page
Which fluids and how much: gearbox oil, coolant, brake fluid?
  • Gearbox oil — SAE 75W-90, 80 ml
  • Coolant — glycol-based, 600 ml
  • Brake fluid — DOT 4 / 5.1 for the front brake and the foot rear brake; DOT 4 for the hand rear brake
  • Grease — silicone on rubber parts, lithium on bearings and pivots
  • Chain — off-road chain lube

Factory fill and Stark's recommendation is Motorex.

from the Stark Varg chat · separate page
Maintenance schedule per the manual: what to service and when?
  • Before and after every ride — lube the chain
  • After every ride — bleed air from the fork, lube the dock latch mechanism, wash the bike
  • 5 engine hours — first oil change (break-in)
  • 15 engine hours or 12 months — fork oil, clean and grease the shock and linkage bearings
  • 40 engine hours or 12 months — fork and shock service, gearbox oil change
  • 80 engine hours or 12 months — inspect motor gears and bearings
  • Every 12 months — replace brake fluid and coolant

Whichever comes first; Stark assigns some jobs to a workshop. Missing the manual's service schedule voids the warranty — keep dates and receipts.

from the Stark Varg chat · separate page
What tire pressure does Stark recommend?

Per the EX manual (cold tires, front and rear):

  • on the road — 2.0 bar (29 psi)
  • off-road — 1.0 bar (14.5 psi)

EX and MX 1.2 tire sizes: 90/90-21 front, 140/80-18 rear.

From the chat: in hard enduro with Tubliss people ride at 0.2–0.3 bar.

from the Stark Varg chat · 19.06.2025 · separate page
What do the LED colors on the remote mean?

EX and MX 1.2

  • blue — charging
  • green — on, ready to ride
  • flashing green — neutral, throttle is not working (press − to get a solid green)
  • red — not ready to ride yet
  • flashing purple (magenta) — update is ready
  • magenta — crawl mode in reverse (hold the lower button)
  • yellow — crawl mode forward (hold the upper button)

First-gen MX: dark blue — charging, light blue — charging with cooling running, red — lights up before shutdown, magenta — update.

From the chat's experience:

  • flashing red on a switched-off bike — sleep mode;
  • yellow indicator on a switched-off bike — the charger is connected to the bike but not plugged into the wall outlet.
from the Stark Varg chat · 07.11.2026 · separate page
How do I wash the Stark properly?

Per the manual

  • switch the bike off and remove the phone from the dock
  • knock off dirt with cold water from a hose
  • no pressure washer — water damages bearings and gets into the wiring
  • body — sponge with a neutral cleaner (pH 6–8), wheels and spokes — with a brush
  • chain — a rag with degreaser
  • rinse with a gentle stream, dry in the sun or wipe dry
  • once dry, lube the chain: rear wheel lifted, turn it by hand and spray lube, wipe off the excess

Don't turn the chain with the throttle — only by hand via the wheel.

from the Stark Varg chat · separate page
What should I check before every ride?

Per the manual

  • tightness of bolts and nuts (per the torque table)
  • tires, pressure, rims and spokes, wheel play
  • brakes: lever travel, leaks, pad and disc wear
  • battery charge — charge if below 20%; the battery vent isn't clogged with dirt
  • coolant level, leaks, fan spins freely
  • chain tension and wear, slider, sprockets
  • wiring and connectors — nothing pinched
  • the phone charges and is paired with the bike, read the error log on the phone
  • suspension: no oil leaks, bump stop intact, shock spring nut tight
  • LED isn't magenta (otherwise update)
from the Stark Varg chat · separate page
Do I need to bleed air from the fork?

Yes, per the manual — after every ride. Bike on a stand, fork fully unloaded: open the bleed screw on top of each leg until the air escapes, then close it.

Fork adjustments: compression — clockwise is stiffer, counterclockwise softer; rebound — clockwise is slower, counterclockwise faster. Set both legs the same.

from the Stark Varg chat · separate page
How do I adjust the brake levers and pedal?

Hand brakes: the adjuster on the lever clockwise — less free play (bite point further from the bar), counterclockwise — more.

Pedal position: loosen the 10 mm lock nut, raise or lower the pedal with the 8 mm bolt, tighten the lock nut.

Pedal travel: loosen the 13 mm lock nut, move the bite point with the 10 mm bolt, tighten the lock nut.

from the Stark Varg chat · separate page
How do I put the Stark on charge per the instructions?
  1. Stand the bike securely on its skid plate on the charging stand.
  2. Press the button on the charging port cover and remove it.
  3. Connect the cable to the bike, then the mains cable to a grounded socket with an RCD.
  4. Hold the On/Off button until the LED turns blue.

Restrictions per the manual: don't charge below +4 °C, after exposure to sea water, near flammables, unattended or under a cover; after charging, disconnect the charger from the bike and the socket right away. If the battery is hot to the touch or swollen, disconnect and don't use it.

Stark video: https://youtu.be/o2_6Vm1RVm4

from the Stark Varg chat · separate page
Where can I find official Stark video guides?

Stark has YouTube playlists with step-by-step videos on removing and installing components. There are about a hundred, with no voice or captions — they only show the work; check the manual for torques.

What's covered: unboxing and assembly, switching on and off, updating, charging; wheels, fork, shock, swingarm, linkage; brakes and master cylinders; chain and front sprocket; gearbox oil change and cooling bleeding, pump, radiator; VCU, wiring, handlebar, dock, control switch, throttle; plastics, subframe, side stand; on the EX — lights, indicators, brake sensors, horn, steering lock.

from the Stark Varg chat · separate page
How do I remove the plastics, spoiler and skid plate? (Stark videos)

MX 1.2 / EX

MX (first)

EX

The videos have no voice — they only show the work; check the manual for torques. The EX shares components with the MX 1.2 — see the MX 1.2 videos.

from the Stark Varg chat · separate page
How do I remove the VCU, battery, wiring and electronics? (Stark videos)

MX 1.2 / EX

MX (first)

EX — lights and sensors

The videos have no voice — they only show the work; check the manual for torques. The EX shares components with the MX 1.2 — see the MX 1.2 videos.

from the Stark Varg chat · separate page
How do I remove the fork, shock, swingarm and wheels? (Stark videos)

MX 1.2 / EX

MX (first)

The videos have no voice — they only show the work; check the manual for torques. The EX shares components with the MX 1.2 — see the MX 1.2 videos.

from the Stark Varg chat · separate page
How do I remove the brakes: calipers, master cylinders, pedal? (Stark videos)

MX 1.2 / EX

MX (first)

EX

The videos have no voice — they only show the work; check the manual for torques. The EX shares components with the MX 1.2 — see the MX 1.2 videos.

from the Stark Varg chat · separate page
How do I service the drivetrain and cooling: chain, sprocket, oil, pump, radiator? (Stark videos)

MX 1.2 / EX

MX (first)

The videos have no voice — they only show the work; check the manual for torques. The EX shares components with the MX 1.2 — see the MX 1.2 videos.

from the Stark Varg chat · separate page
Sea to Sky 2026: where, when and who won?

Sea to Sky 2026 took place October 8–10 in Kemer (Turkey), the 7th of 8 rounds of the FIM Hard Enduro World Championship. It consists of three races: the Beach Race, the Forest Race and the Mountain Race (64 km, 16 checkpoints, finish on the summit of Tahtalı, 2,365 m).

Mountain Race result (provisional, after Kabakchiev's disqualification)

  1. Manuel Lettenbichler (KTM) — 3:40:01
  2. Mario Román — +4:11
  3. James Moore — +14:26
  4. Mitch Brightmore
  5. Thomas Scales
  6. Ashton Brightmore
  7. David Cyprian
  8. Alfredo Gómez
  9. Danila Chernyaev — +51:23
  10. Dieter Rudolf
  11. Graham Jarvis — on his electric bike, the Jarv-E: the first electric bike to finish Sea to Sky

Mitch Brightmore won the Beach Race and Teodor Kabakchiev won the Forest Race. In the Mountain Race Kabakchiev came in second and got a 10-minute penalty for help from spectators (they removed barbed wire from his wheel). After a protest he was disqualified, which he disputes.

The final round of the season is Hixpania Hard Enduro, October 23–25, Spain.

from the Stark Varg chat · 10–11.10.2026 · separate page
Who from the chat rode Sea to Sky 2026, and how does the Stark handle this race?

Chat members at Sea to Sky 2026

  • One member rode a Stark. Forest race: 28 km, 6 of 9 checkpoints. Mountain race: 28 of 42 km; reached CP 7 two minutes before the time bar with 23% charge and retired — not enough charge or time to continue. Started the mountain race 268th of 329. Finisher. The beach race was spoiled by the chain. Forest race video: https://youtu.be/Wv-jmWVUDj0
  • Another rode a KTM, made the time bar and reached the finish.
  • Another rode a Stark. In the optional Special Race he dropped the bike on rocks — the front sprocket broke along with the carbon guard. Twice he went fully underwater with the Stark — the bike survived.
  • Another rode a Husqvarna. According to him there were four Starks at the race; the Stark's plus is that it's easy to scout the canyon on foot with it, the minuses are weight and battery.

The Stark at Sea to Sky — experience

  • On one battery Starks reach roughly checkpoint 7; bronze gate is CP 6, from CP 6 to 7 it's already silver.
  • To go further, riders plan a second battery swapped at a checkpoint — CPs are almost always next to a road. Opinions on the swap differ: some say "5 minutes", others took over an hour in a workshop — without a support crew it will be hard in a race.
  • Crashing is expensive: rocks hit the sprocket and guards, and in deep sand the bike is hard to lift.
  • One Stark rider covered 40 km with 5% left; another finished on a Stark with 4%.
  • Anyone who reaches at least the first checkpoint of the mountain race counts as a finisher.
from the Stark Varg chat · 09–14.10.2026, 11–14.10.2026, 08–10.10.2026 · separate page
Stark or a gas enduro bike (KTM, Husqvarna, Beta, Yamaha) — what's the difference?

What owners who switched from gas praise

  • instant pull without clutch or gears — climbs are easier, on descents it's easy to control the bike with your feet down
  • faster in motocross: at 50 hp it pulls away from amateurs on KTM 350/450; after a Honda CRF 250 — 3 seconds off a one-minute lap
  • silence, no exhaust, no engine oil; many sold their gas bikes after the Stark
  • Stark won the manufacturers' team classification in the FIM SuperEnduro World Championship (2026)

Downsides compared with gas

  • range: on long hard races a tank lasts longer — at Sea to Sky a Stark reaches about CP 7 on one battery
  • weight: the EX is about 120 kg, noticeably harder to lift than a 300 TBI
  • no clutch — in extreme hard enduro and slow technical sections some miss it
  • charging, service only via Stark support, long waits for warranty parts

The chat's verdict: for motocross, cross-country and moderate enduro many prefer the Stark; for multi-hour hard enduro without recharging, gas is still more dependable. The chat rules ask to compare on the merits.

from the Stark Varg chat · 03.12.2024, 29.06.2024, 13.03.2026 · separate page
Stark or Arctic Leopard (XE, "Cheetah") — which to choose?

Arctic Leopard E-XE 880 ("Cheetah") — per sellers' data: about 108 kg, peak about 37 kW (~50 hp), battery about 6–6.75 kWh, noticeably cheaper than a Stark.

Stark Varg EX / MX 1.2 — 120 / 118 kg, 60–80 hp, 7.2 kWh battery, liquid cooling of motor, battery and inverter.

Opinions in the chat

  • the Arctic is lighter and cheaper; about 1.5 times less powerful, comparable range, and at an easy pace it may go further
  • the Arctic can overheat on hard climbs — the Stark's cooling is better
  • there are complaints about the Arctic's build quality (caliper centered with a washer, a loose bushing in the wheel, plastics); an owner who rode one for 10 months complained about suspension and power, switched to a Stark and is happy — the only thing he liked about the Arctic was the weight
  • an Arctic seller in the chat notes the Leopard only needs charging and gearbox oil, with no "fatal" problems

In short: the Arctic is lighter and cheaper; the Stark is more powerful, with better cooling and suspension, but heavier and pricier.

from the Stark Varg chat · 02.01.2025, 24.11.2025, 29.04.2025 · separate page
Stark or Surron Ultra Bee / Talaria?

These are bikes of a different class — lighter, simpler and cheaper.

  • Surron Ultra Bee — per sellers' data: about 88 kg, peak about 21 kW (~28 hp), 4.4 kWh battery
  • Stark Varg EX — 120 kg, 60–80 hp, 7.2 kWh, full-size motocross suspension

Opinions in the chat

  • someone who owns both a Stark and a Surron: "the Surron is a solid VW Polo compared to a Porsche"
  • the Ultra Bee is praised for being undemanding: two winters in snow and water without problems
  • according to someone who switched, the Talaria lacks power for serious enduro

For easy rides, kids and park riding a Surron or Talaria fits better; for enduro racing and motocross — the Stark.

from the Stark Varg chat · 21.04.2025, 01.01.2026, 15.05.2026 · separate page
What is the Jarv-E, and how does it differ from the Stark?

Jarv-E is an electric hard enduro bike developed with Graham Jarvis and built in Austria; pre-orders in Europe, first deliveries from spring 2026.

  • per the manufacturer: 50 kW, 95 kg, 5.6 kWh battery, quick-swap — about 30 seconds to replace
  • the Stark EX: 60 kW (Alpha), 120 kg, 7.2 kWh, battery not quick-swap

Jarvis on the Jarv-E finished 10th at Erzbergrodeo and 11th at Sea to Sky 2026 — the first finish of an electric bike at Sea to Sky.

In short: the Jarv-E is lighter and has a quick battery swap, which matters for long hard enduro; the Stark has a bigger battery and more power, and it's already on sale.

from the Stark Varg chat · separate page
How do I check battery cell imbalance, and how do I reduce it?

How to see it: use VargLink — varg.aupov.tech. It shows not only cell imbalance but also helps with proper charging and diagnostics.

How to reduce it

  • in VargLink set the Storage (1 kW, 60%) mode and leave the bike on charge like that for a few days; you can watch the imbalance go down remotely
  • another tip from the chat: set slow charging to 80% and leave it until the imbalance is gone

With a large imbalance it's not recommended to balance at 100%: some cells may get overcharged.

from the Stark Varg chat · 20.10.2026 · separate page
What is the latest Stark Varg firmware, and what's new in 1.15.0?

The latest is 1.15.0 (October 2026, released together with app 3.4.0/3.4.1). It rolls out to both the EX and the MX. If the app says the latest is 1.12, update the app anyway: after that it offers 1.15.

How to update: app 3.4.1 downloads the firmware over your phone's Wi-Fi and installs it on the bike. A working SIM card in the modem is no longer required.

What changed in 1.15.0

  • new secure communication with the phone: only a phone with a Stark account can connect to and unlock the bike
  • because of this, third-party apps can't connect on 1.15: VargPilot, DV Watch, Svag
  • VargLink works with 1.15 (from version 0.27, varglink.com). It shows and changes charging and riding modes alongside the official app

Before updating from 1.12: if you use VargPilot, keep in mind that it won't connect on 1.15.

Timeline: 1.10.0 – May 2026, 1.11.0 – June, 1.12.0 – July, 1.15.0 – October.

from the Stark Varg chat · 09–11.10.2026, 15.10.2026, 01.11.2026 · separate page
Which firmware version introduced traction control?

Traction control arrived with firmware 1.11.0 (June 2026). It's built into the power modes screen: the level is set separately for each mode.

  • as standard — only on the Alpha version; Standard doesn't have it in the app
  • on 1.10 and earlier there is no traction control
  • on 1.11, some riders found that maps and traction settings got reset after the bike had been off for a long time — this was fixed in 1.12
from the Stark Varg chat · 08–24.09.2026, 15.10.2026, 24.08.2026 · separate page
Has anyone fitted an X-Trig triple clamp on the Stark, and how does the phone mount work with it?

A chat member has an X-Trig triple clamp fitted.

The phone mount works fine with it, but the holes in the panel the phone sits in had to be drilled out 1 mm upward.

from the Stark Varg chat · 20.10.2026 · separate page
The Stark phone (Arkenstone) shows an engineering menu or strange screens instead of the app — why, and what to do?

If the volume up button on the Arkenstone is held down at power-on, the phone boots into the engineering menu.

This happens when a button stays pressed after a hit to the right side of the phone (e.g. the upper volume button).

What helped in the chat: restart the phone. One owner first got garbage on screen, then heard three sounds, and after a restart everything was back to normal.

from the Stark Varg chat · 22.10.2026 · separate page
Which grips fit the Stark Varg, and how do I fit lock-on grips to the throttle?

On ODI the left grip is lock-on (with clamps), and the right one is glued or wired.

Lock-on on the throttle: an adapter has been made for this long ago, and many chat members already run such grips.

How to fit:

  • drill a hole in two self-tapping screws with a 2.6 mm drill
  • undo them with Torx T10 and replace them with 4 mm self-tapping screws of the same length and thread pitch
  • take the magnet insert from makerworld, version 2
from the Stark Varg chat · 22.10.2026, 23.10.2026 · separate page
How can I improve the rear brake on the Stark, and where can I get an adapter for a front caliper?

A chat member used a special adapter to fit a Brembo front caliper in place of the stock rear caliper, increasing braking force at the rear wheel.

The adapter is made by @dabwase. It lets you mount a front 2-piston caliper on the rear wheel, which improves braking and reduces the lever effort needed.

from the Stark Varg chat · 23.10.2026, 29.10.2026 · separate page
What brake discs come standard on the Stark front and rear, can I fit a larger one or one from another bike, and where can I buy one?

The standard front brake disc is 260 mm.

You can fit a larger 270 mm disc. It needs an adapter that mounts the caliper for the bigger disc.

The standard rear disc is 220 mm, and you can fit a 240 mm one. For the larger rear disc you need a niceCNC adapter.

If you don't want to buy the OEM ones, brake discs from KTM fit.

You can buy discs and the front adapter from @kalina_s_24.

from the Stark Varg chat · 23.10.2026, 04.11.2026 · separate page
Where can I get the 3D-printable tool box model for the Stark Varg, and what fits in it?

The "Stark Varg Tool Box" model is on MakerWorld: https://makerworld.com/models/3456970. It holds a couple of wrenches, a ratchet, an extension and Torx bits. The model page has a video showing what fits inside.

from the Stark Varg chat · separate page
How do I get a "free-wheeling" effect (coasting like on a 2-stroke) on the Stark Varg?

Set regen to 0 and coast. Only turn regen on for descents, by switching maps (modes) on the downhill. Downside: switching maps with the buttons on the handlebar controller while riding is awkward, and you can miss the button.

from the Stark Varg chat · separate page
How do I get a little free play (slack) in the throttle on the Stark Varg?

Install an adapter in the throttle tube for lock-on grips. It gives the throttle a little extra travel, i.e. a bit of free play, roughly like on a KTM. You can also ride without the adapter, it's a personal preference. One member didn't like that free play.

from the Stark Varg chat · separate page
Who makes high-quality graphics (stickers) for the Stark Varg with minimal gaps?

Two options were recommended in the chat: @evgenyp_pgpp and BSGX.

from the Stark Varg chat · separate page
How much oil should I put in the Stark Varg gearbox?

You need 80 ml, even though the gearbox can physically hold up to 900 ml.

from the Stark Varg chat · separate page
Can I charge a Stark from a generator at a race, and what should I watch out for?

You need an inverter generator. The stock charger adds roughly 1% per minute, so for enduro races it's painfully slow, but for motocross with 1–2 hour breaks between motos it works fine. In mountain races it's an option only as a last resort: at one of them charging took 1 h+.

from the Stark Varg chat · separate page
What is the difference between the Stark MX1 gen1 and gen2?

According to one member, almost nothing: only the inverter cover and the charging port. The first generation had problems with the charging port. Don't confuse it with the MX 1.2: new bikes are only sold as the MX 1.2, which is considered better (one member thinks it's not by much).

from the Stark Varg chat · separate page
Can the warranty on a Stark be extended or reissued if it has already expired?

No, it can't.

from the Stark Varg chat · separate page
Where can I get parts from dismantled Starks (donor bikes)?

Gencho sometimes has parts from dismantled Starks.

from the Stark Varg chat · separate page
How much does a motor for the Stark Varg cost?

Around three thousand euros. That's the price in the EU.

from the Stark Varg chat · separate page
Inverter temperature readings fluctuate wildly — what is it?

Most likely the inverter temperature sensor is faulty, rather than it being an app error. The sensor is only replaced together with the motor. In theory the sensor itself can be replaced, but nobody has done it.

from the Stark Varg chat · separate page
The engineering menu pops up on my phone screen — what should I do and why does it happen?

Restart the phone. Most likely the cause is a stuck button (for example, after an impact on the right side): if the volume up button is held down when the phone powers on, you end up in the engineering menu.

from the Stark Varg chat · separate page
Who has improved the rear brake on the Stark, and who should I ask for their experience?

Owners in the chat have improved the rear brake by fitting a front 2-piston Brembo caliper in place of the stock rear caliper, using an adapter. The adapter is made by @dabwase. For first-hand experience, ask in the Stark Varg chat.

from the Stark Varg chat · separate page
How well suited is the Stark Varg to hard enduro, and what are its weak points?

According to one group's experience, most of them switched to Stark: in hard enduro it's more durable than the TB. By their account, the problems with the gearbox dogs, rear brake, tires and radiators are no longer an issue. The downsides: the phone (app), the remote and the carbon parts, but none of that is fatal. The main drawback is range: on tracks of 50+ km (mountain races can run up to 78 km) you need spare battery capacity, charging or battery swaps. Another member finds the Stark delicate: the carbon breaks in a minor fall, and the wiring near the throttle and the wires low down by the handlebars are vulnerable.

from the Stark Varg chat · separate page
Can a mechanic help swap the Stark battery during the S2S race?

According to the S2S organizers, you have to ride to the start on the bike, and you can only swap the battery yourself. A mechanic can only bring the battery.

from the Stark Varg chat · separate page
Is it enough to change the fork oil by just unscrewing the fork leg nut, draining the oil and pouring in new oil?

No, that's not enough. This only drains the outer circuit, while the closed circuit (the cartridge) stays as it is. You need to open both the cartridge and the outer circuit, flush them, lubricate the seals, and unscrew the piston from the cartridge. The fork leg is held in a vise while you do this. Some of the tools can be 3D-printed. If you don't have the tools, it's better to take the fork to a shop.

from the Stark Varg chat · separate page
What screen can I put on the Arkenstone remote/dash instead of the stock one — from which phone?

Only the original one — there are no alternatives.

from the Stark Varg chat · separate page
Is there an official video on washing (cleaning) the Stark VARG?

Yes, "How to Clean the Stark VARG (Official Guide)": https://www.youtube.com/watch?v=SnVUMbp4l78

from the Stark Varg chat · separate page
How does WP PRO suspension on a 250 gas bike differ from the stock Stark suspension, based on an owner's experience?

After ~3 months on a Stark in motocross, Sergey_D switched to a 250 with WP PRO. By feel, the suspension is noticeably better: it soaks up small stuff very softly and confidently. It took about 15 minutes to get used to the brakes and gearbox. He is thinking about putting PRO suspension on the Stark. The KTM triple clamp should apparently fit, and the shock should be from 2016–2022 models (not verified).

from the Stark Varg chat · separate page
Does the selected country affect the price of the Stark warranty extension, and which option is cheaper?

Yes, the price depends on the country you pick in the form. According to members, going through Georgia (an address in Tbilisi) works out cheaper, especially for a two-year extension. Recently reported prices: Germany — €599 per year, Georgia — $690. Previously the amount didn't change: 999 in both euros and dollars for two years. This "bug" may have been fixed.

from the Stark Varg chat · separate page
What details do I need to enter in the form when paying for a warranty extension?

The form has to be filled out completely: the payment won't go through if any fields are left empty. You need to enter an address, country, postal code and phone number. You can use your own phone number.

from the Stark Varg chat · separate page
Which springs fit the brake lever on the Stark Varg, and are they needed?

The Stark Varg EX has no spring in the lever (the designers did without one), while the MX does have one. Without it, the lever has about 1 cm of free play. The fix: take a compression spring 0.5×5×25 mm (wire diameter × outer diameter × length, 304 stainless steel) and insert a 0.5×4×25 mm spring inside it. According to the author, this gives the ideal lever force. They are sold on marketplaces in packs of 10.

from the Stark Varg chat · separate page
How can I check the cell imbalance of a Stark Varg battery, and how do I reduce it?

You can check the imbalance in a third-party app, for example VargLink (varg.aupov.tech). To reduce it: in VargLink set Storage mode (1 kW, 60%) and leave the bike on the charger for a few days. Another tip from the chat: set the charge limit to 80% on slow charging and leave it until the imbalance goes away. Balancing large imbalance values by charging up to 100% is not recommended: some of the cells may end up overcharged.

from the Stark Varg chat · separate page
Which app is best to use instead of VargPilot?

VargLink is the one people recommend: going by feedback in the chat, it ranks first and works better than the other unofficial apps.

from the Stark Varg chat · separate page
Is there a solution for the Stark Varg throttle grip to fit standard KTM grips if there's no suitable disc?

There is a solution: 3D-print a map disc for standard KTM grips. Model: https://makerworld.com/models/3354424. One member wasn't able to open the grip to swap the disc.

from the Stark Varg chat · separate page
Which way should the throttle cable/wire be routed, and how can I protect it from damage?

The advice is to route the throttle wire downward rather than forward in the direction of travel, since that makes it less likely to get damaged. One rider runs a niceCNC grip guard, with his wire pointing up.

from the Stark Varg chat · separate page
What symptoms can show up if water gets under the cover of the electric drive unit (the unit by the motor) on a Stark, and what helped?

After water got in under a cracked cover, the bike started acting up: the red indicator would come on and the drive would cut out; after a reboot it didn't always return to normal right away; then the motor wouldn't spin at all and jerked back about a centimeter when switching from reverse to forward. What helped was flooding all the wires with electrical contact cleaner in the garage — after a couple of days it was working again.

from the Stark Varg chat · separate page
Are there carbon covers for the Stark, and how much does a set cost?

CMT makes the carbon covers. The set is sold at StarkShop.

from the Stark Varg chat · separate page
What coolant should I use in the Stark Varg, and how often should I change it?

According to the manual, it should be changed about once a year (though with a caveat — "I think"). The manufacturer recommends Motorex. One member went 2 seasons and 100 engine hours without changing the coolant.

from the Stark Varg chat · separate page
How can I check whether the Stark Varg inverter is overheating if I hear a strange noise or suspect overheating?

Check the inverter temperature in VargLink, in the diagnostics section. There are about 3 sensors there. The values are read in the moment, in real time.

from the Stark Varg chat · separate page
What tires should I run for hard enduro?

Tip from the chat: X-Grip Enduro works great everywhere (mountain races, creeks, roots, rocks, traverses) with no problems. In colder weather, go with the Michelin Medium 1. For hard enduro, in the author's opinion, you don't need any other tires.

from the Stark Varg chat · separate page
Where can I get an aluminum throttle housing for the Stark Varg?

People in the chat mention Nice CNC and Emex, and Nice CNC is the better of the two. It's a cover that goes over the stock housing, and it works great. Making a completely new housing is difficult because the sensor has to be moved over.

from the Stark Varg chat · separate page
What should I do if, after the Stark app update, it asks me to log in, but I bought the bike used and it's linked to someone else's account?

There's no quick fix: the bike has to be transferred to your account. It's best to contact the previous owner so they can transfer the bike to your account. Or contact Stark support: first create an account on starkfuture.com, then submit a bike transfer request. Temporary workaround: install the VargLink app. If the bike's firmware is below 1.15, it doesn't require an account.

from the Stark Varg chat · separate page
How do I check the firmware version of a Stark motorcycle if the stock app won't let me in?

Install the VargLink app (varg.aupov.tech). It shows the firmware version.

from the Stark Varg chat · separate page
What proof is needed to transfer a Stark motorcycle to another account through tech support?

Tech support will ask for the grounds for the transfer. They suggested drawing up a bill of sale.

from the Stark Varg chat · separate page
How do I diagnose a Stark motorcycle if my phone can't see it and the LED is red?

The official app has no diagnostics. Install VargLink, preferably on the phone you use with your Stark. It runs alongside the official app and doesn't interfere with it. A red LED can point to throttle problems. If the bike has been transferred to your account and your phone still can't see it, only Stark support can help. You can still ride in this state.

from the Stark Varg chat · separate page
What does the warning in the Stark app about the SIM card APN mean?

It's not critical: the app is just complaining about the SIM card's APN.

from the Stark Varg chat · separate page
What should I do if my Stark Varg shut down at low charge at full throttle and won't turn on?
What should I check if the bike won't turn on after shutting off at low charge and the FAQ advice didn't help?

Check the high-voltage outputs to the inverter with a multimeter. You can also give your battery to another Stark owner with an MX and try connecting it to their bike.

from the Stark Varg chat · separate page
What happens if you ride a few km without oil in the gearbox (for example, the cover is punctured), and what should you do afterwards?

Nothing terrible, the main thing is that nothing gets inside. After replacing the cover and filling with oil, spin the gearbox, drain the oil right away and check for metal shavings.

from the Stark Varg chat · separate page
Which Blackview 6300 fits the MX: the regular one or the Pro?

The Blackview 6300 Pro is the one that fits: it has wireless charging. The non-Pro model doesn't have it, so it isn't suitable for the MX.

from the Stark Varg chat · separate page
What navigation app can I use on my phone with the Stark to load a race track and follow it?

VargLink has no built-in navigation. Chat members recommend third-party apps: Osmand and Organic Maps (some have ridden with it and say it's "pretty decent"). You can split your phone screen and run the navigation app next to the native app.

from the Stark Varg chat · separate page
After the automatic update, the Stark app sees my bike (MX Gen2) but demands a mandatory firmware update over Wi-Fi and won't let me control the bike; the update fails with an error. What should I do?

Most likely the new app is incompatible with the old firmware. You can roll the app back to an older version (the other rider had 1.0.187), and then everything works. You can download old versions through apkcure, for example. It's better to update the firmware the old way, via the modem, first.

from the Stark Varg chat · separate page
What happens if I factory reset my phone when I need the old Stark app?

After a reset, the version of the Stark app that came preinstalled on the phone is still there, but it is very old and immediately asks you to update. Manually changing the system date doesn't help: for one chat member, all Google services stopped working, including the store.

from the Stark Varg chat · separate page
Can I update the firmware if there is no modem, and how do I transfer it to a bike with an unflashed board?

Have the modem flashed on the mainland – the update comes through normally. You can also swap in the upper board from a bike that already has the new firmware, but the boards must be identical: you can't mix EX and MX 1.0.

from the Stark Varg chat · separate page
Can I enable traction control in the Fenr app on an EX with 60 hp?

No, Fenr doesn't have that option.

from the Stark Varg chat · separate page
What can I use to check the battery status of a Stark motorcycle if I don't need VargPilot?

Install the VargLink app and check the varg.aupov.tech website. In the app, tap the word "battery" on the main screen. A cell imbalance of 10 mV is very small, so everything is fine.

from the Stark Varg chat · separate page
The app won't connect to the bike. What could be the cause and what should I do?

The bike's firmware may be listed as outdated on Stark's server. Ask Sam on the Stark website which firmware version is listed for your bike.

from the Stark Varg chat · separate page
What should I do if my Stark Varg won't connect to the stock app after it was connected from another phone?

Delete the Bluetooth pairing on your phone that is named after the bike's VIN – it goes stale. Sometimes the Varg also won't connect on its own (even without VargLink) until you reboot your phone.

from the Stark Varg chat · separate page
Which version of the stock Stark Varg app works better on Android: the Google Play one or the one on the Arkenstone?

According to one member, the Google Play app behaves better than the one on the Arkenstone. The stock app on the Arkenstone sometimes glitches, and restarting the Arkenstone helps.

from the Stark Varg chat · separate page
What should I do if the stock Varg app shows "no updates" but an update should be available?

Tip from the chat: turn on a VPN and restart your phone (a normal reboot). After that, the update shows up.

from the Stark Varg chat · separate page
Which charger should I get for an Apple Watch if I mount it on the bike?

You need a good-quality charger with a magnet. The cheap ones only pretend to be chargers and don't actually charge. For mounting, it's better to make a case so the watch doesn't fly off. The idea of a power bank with a magnetic holder and wireless charging was considered a decent one.

from the Stark Varg chat · separate page
What should I do if the answer to my question isn't in the FAQ?

Ask the bot @starkvarg_help_bot or post your question in the chat. Good answers will be added to the database and to the website.

from the Stark Varg chat · separate page
Do I need a working Arkenstone with the app running and a network connection to set up VargLink on another phone?

No, you don't need a working Arkenstone to set it up. For now, VargLink will work on any Android phone.

from the Stark Varg chat · separate page
Why won't another Android phone connect to the bike via VargLink while Arkenstone is running? What should I do?

Arkenstone can occupy the bike's channel: the channel is exclusive, one channel – one phone. You need to shut Arkenstone down completely. If that doesn't help, send the logs to the developer. Also check that the bike's information appeared in VargLink after you entered your login and password from the Stark website.

from the Stark Varg chat · separate page
What is known about the new upper triple clamp (top yoke) on the 2026 Stark, and how much does it cost for the SM and EX?

According to the listing, the new top clamp is described as being for the SM, but it has been seen on a 2026 EX (on Artur Gorbatovsky's bike). Price: $249 for the SM, $209 for the EX. The pictures of the two look identical, but Daniil Blagodetelev claims the SM clamp is wider, meaning they are different parts.

from the Stark Varg chat · separate page
Which Stark models have rubber dampers in the upper triple clamp?

According to owners, the older EX triple clamps have no rubber dampers, while the MX and MX 1.2 do. They tear quickly. Some people believe the dampers are why the handlebar ends up bent after a crash. The new 2026 triple clamp has no dampers.

from the Stark Varg chat · separate page
Do Leopard (Cheetah 880) electric motorcycles overheat, and what does it depend on?

According to owners, since 2025 Leopard has had no overheating problems, compared to bikes from before 2025. With the 12-tooth sprocket there are no problems at all. You can still overheat it if you push against a wall or a steep bank and sit there under load. When discussing this, always ask which model year it is. Leopard's suspension and build quality are worse than Stark's.

from the Stark Varg chat · separate page
Do I need to register the Varg through support to install it, or is there something else that needs to be registered?

What you need to register through support is not the Varg, but the Arkenstone.

from the Stark Varg chat · separate page
Which bleed valves (for releasing pressure) should I fit on the fork, and is it worth using them instead of the bolts?

Any valves with an M5 thread will work, and there are plenty of Chinese ones on marketplaces. Opinions are split. The upside: the fork stays cleaner and you don't have to reach for a screwdriver. The downside: many people consider them unreliable. Dust and dirt get in, even expensive ones leak, oil can come out through the valves, and you can strip the thread. Bolts with manual bleeding using a screwdriver are simpler and more reliable. One member bleeds the pressure with a screwdriver after every training ride.

from the Stark Varg chat · separate page
How can I reduce the risk of the battery, motor and controller failing ("puking") on a Stark?

Install VargLink, keep an eye on cell imbalance in the battery and balance the cells in time. It was also mentioned that you shouldn't discharge the battery below 20% (the person asking heard this, and it wasn't confirmed in the chat). Don't overheat the motor: when you ride at full power (around 80 hp) from one traffic light to the next, it heats up.

from the Stark Varg chat · separate page
How can I try to clean the brake if it isn't working well?

Sometimes it helps to ride in reverse and press the brake a couple of times — that cleans the brake.

from the Stark Varg chat · separate page
How do I install Varg Pilot?

Varg Pilot can only be installed via ADB.

from the Stark Varg chat · separate page
Is it normal for a switched-off bike to lose 13% charge after sitting for a week?

Yes, that's normal. According to VargLink statistics, self-discharge is about 2% per day.

from the Stark Varg chat · separate page
When does the bot @starkvarg_help_bot reply in the chat on its own, and which messages does it skip?

It replies if a question has gone unanswered for more than 10 minutes. It skips rhetorical questions and emotional posts, jokes and banter, questions aimed at a specific person ("are you going?"), clarifications directed at the person you're talking to ("do you mean the other one?"), short remarks that only make sense within the conversation, and questions that have already been answered in the thread.

from the Stark Varg chat · separate page
Who services Kayaba suspension and prints replacement carbon guards for the Stark?

According to Denis Ayupov, it's @Extrimall91. The quality of the work hasn't been verified in the chat.

from the Stark Varg chat · separate page
How do I add information to the chat bot's knowledge base?

Message the bot with "Запиши" ("Write it down") and say what needs to be added to the knowledge base.

from the Stark Varg chat · separate page
What kinds of defects show up on new Stark bikes?

Defects have been reported even on brand-new bikes: a faulty throttle grip on one, and on another, bad wiring from the phone dock that kept the bike from powering on until you turned the handlebars.

from the Stark Varg chat · separate page
What can I use for navigation and tracks if I don't have a paid subscription?

You can use the OsmAnd app. One of the members has ridden with it: it's convenient and has voice prompts.

from the Stark Varg chat · separate page
How do I change the power: in Swag or in another app?

You can't change the power in Swag. It has never been possible there. You can do it in VargLink, but only on Android. There is no iOS version yet.

from the Stark Varg chat · separate page
Is there a cheap alternative to USWE covers?

Yes, there are e-gear covers. They're about 3 times cheaper than USWE and are available on marketplaces.

from the Stark Varg chat · separate page
What's the better buy: a used 2025 Stark MX 1.0 with low mileage, or a new MX 1.2 (with a noticeable price difference)?

The MX 1.0 has a weaker battery, and the suspension on the new MX is better than on the old one. A used bike can also be a good option if you have it checked over. But new is new.

from the Stark Varg chat · separate page
Why can't you just build a Stark battery from pouch cells instead of cylindrical cells?

The problem isn't so much the weight as the fact that you can't build 400 V from pouch cells, and all the electrics are designed for 400 V.

from the Stark Varg chat · separate page
Where can I find the stock app on the Arkenstone after installing VargPilot?

In the device settings.

from the Stark Varg chat · separate page
How do I enable 3.3 kW charging in the stock Stark Varg app if only 2 kW max is available?

Select Austria as the region and update the app — after that the 3.3 kW option appears. It's worth checking the actual charging power separately: people in the chat doubted that it really draws more than 2.3 kW.

from the Stark Varg chat · separate page
What shim stack is in the fork and shock on the Stark Varg MX, and can I use it as a reference?

There's no single stack: it's not just about the shims, and everyone's setup is different. Even within the same shipment, the stack can differ.

from the Stark Varg chat · separate page
Which iPhone app shows battery (BMS) status on firmware 1.15?

No iPhone app works with 1.15. You can install VargLink on a different phone (a native, non-iOS one), and it will show the battery status. FENR haven't added 1.15 support — possibly Apple doesn't allow that kind of implementation.

from the Stark Varg chat · separate page
What is known about the issue where the sensors for one half of the battery drop out while charging (after a firmware update)?

After a firmware update, half of the cells go offline in VargPilot and the bike stops charging. First half of the sensors drop out, then the BMS goes into protection, and for some reason the error gets logged against the inverter rather than the BMS. VargLink can now recognize the problem from indirect signs and shows a clear error message. The suspect is the ribbon cable between the two halves of the battery. A possible fix: open up the battery, reseat or clean the ribbon cable between the halves, and reassemble it with sealant. This is a suspicion, not a confirmed conclusion.

from the Stark Varg chat · separate page
How are the battery sections connected in the Stark Varg MX?

A latched ribbon cable and a gold-plated spring activator between the sections. This applies to the MX; in the author's opinion, little has likely changed inside. The balancer in the battery is weak, a "pathetic imitation" of a proper one. Dead cells act as a jumper that lets current pass through, so sections can die while the battery keeps working for some time.

from the Stark Varg chat · separate page
Is there a common battery problem with the Stark Varg, and which models does it affect?

There is a battery problem on all models, both the MX and the EX. From the service's experience, cell 41 "drops off" on all of them: they have already seen 7 such batteries with the same diagnosis.

from the Stark Varg chat · separate page
What happens to the Stark Varg battery if one cell drops to zero or below 2.7 V, and how is it fixed?

When a cell drops to zero or below 2.7 V, the BMS goes into protection and the battery stops charging. One dead cell is enough to shut down the whole battery. The fix is to replace the cells. The BMS only manages the battery; it isn't powered directly by it.

from the Stark Varg chat · separate page
What power level is best to start learning double blips on the Stark Varg?

35–40 hp is enough to start with. At 50 hp it's scarier, because the second throttle blip comes out abrupt until you've built up the skill.

from the Stark Varg chat · separate page
How do I soften shock compression, and what should I check if the rear suspension hits hard on a log?

Turn the gray knob (compression) 4–6 clicks toward minus, i.e. back off the compression, and check your sag. The stock Kayaba is stiff if the rider weighs less than 90 kg.

from the Stark Varg chat · separate page
Can I write my own app for Amazfit watches?

Yes, if the watch runs Zepp OS (almost all modern models, starting with the GTR 3 / GTS 3 series and newer). Development for the platform is open to everyone, and apps are built with standard web technologies.

from the Stark Varg chat · separate page
Does DW Watch work with bike firmware 1.15.0?

Yes. DW Watch version 0.85 and later (phone installer 0.80 and later) works with firmware 1.15.0, which introduced authorization, via your Stark account. The earlier claim that they don't connect on 1.15 is incorrect.

from the Stark Varg chat · separate page
Where can I find the Stark Varg EX owner's manual?

The manual is digital only, there is no paper version. You can find it at https://starkfuture.com/tutorials-and-technical. Direct link to the PDF: https://assets.starkfuture.com/frontend-assets/cms/technical-documents/Stark%20VARG%20EX%20Owners%20Manual%20ENG%202025.pdf

from the Stark Varg chat · separate page
Can I put WP oil in KYB (Kayaba) suspension?

Yes, people do it. One member says most Starks in the city are run this way with no complaints, and the suspension feels a bit softer. Another member talked to specialists, and they said there's no difference.

from the Stark Varg chat · separate page
How can I find the cause of a check engine error if the Stark won't turn on or blinks green, and replacing the throttle and the dash/switch unit didn't help?

Download the Varglink app (https://varglink.aupov.tech/) and read the error codes. People in the chat also recommended Denis's app (Denisvarg). If you've already ruled out the throttle and the buttons, next check the battery, the VKU, the inverter and the wiring (a wire could have come loose or been damaged).

from the Stark Varg chat · separate page
Can I connect the bike directly to a Garmin or Apple Watch over Bluetooth?

No. Bluetooth on these watches is limited. You can pair sensors with them, but the watch sees the bike without asking for a PIN code, and the connection ends there. So the watch has to be connected through your phone. With Garmin, everything works through apps on the phone.

from the Stark Varg chat · separate page
How do I check the HV (high-voltage circuit) resistance of the inverter on a Stark Varg?

Multimeter: put the black probe (negative) on the positive contact and the red probe (positive) on the negative contact of the orange HV connector coming from the inverter. If the reading between measurement points 6 and 7 is more than 5 kΩ, the HV resistance is normal. Zero resistance means a short circuit.

from the Stark Varg chat · separate page
Is it difficult or dangerous to switch to a throttle grip with a lock-on (adapter)?

Opinions differ. One user says it's no trouble: the adapter is easy to install, he runs one himself, he lifts the bike by the throttle grip from the other side, and racers ride with it in tough conditions without any problems. Another member broke the magnet in the throttle grip because of a defective adapter and advises not to take the risk.

from the Stark Varg chat · separate page
How can I switch off charging of the bike from my phone if it can only be stopped with the remote or by unplugging it from the socket?

You can install a Tuya smart socket: VargLink can switch it off (the integration works only with Tuya). The socket has to be connected to the internet. Alternatively, set the charging current to 0.3.

from the Stark Varg chat · separate page
Can I configure the bike's programs (modes) on a smartwatch with VargLink?

No, the watch isn't used for configuring programs. Programs are configured on your phone in VargLink and in the stock app.

from the Stark Varg chat · separate page
Why are cells #1, #50, #51 and #100 the ones that most often go out of sync in the battery data?

The battery is 100 series groups of 4 21700 cells each (400 cells in total). It is made up of two halves, each with its own BMS board (the logs show two firmware versions: bmsPos and bmsNeg). One board measures groups 1–50, the other measures groups 51–100. #1 and #100 are the ends of the chain at the power terminals. #50 and #51 are the joint between the halves, where the power jumper is. The outermost groups sit next to the contactors and the thick cables, so they run warmer when riding and charging, and they behave differently in the cold (on cold batteries the edge groups read above the median, on warm ones below it). The outermost channels of the BMS boards are tied to power and ground, so they are the first to pick up an offset.

from the Stark Varg chat · separate page
Why is a low-voltage battery (around 50 V) worse than a high-voltage one like Stark's?

At low voltage, the same power requires much more current. For 19 kW at 50 V (14s22p) you need roughly 350–400 A, whereas Stark runs about 50 A. Because of this, you need thicker cables. A low-voltage battery is cheaper to build. The cells in such a battery are outdated and cost about half as much to buy as Stark's.

from the Stark Varg chat · separate page
How can I add lights to the MX if I don't want to mess with the stock wiring (for example, powering a headlight from the pump)?

It's easier to mount a battery-powered light on the handlebars than to mess with the stock wiring.

from the Stark Varg chat · separate page
Can I power a headlight from the pump connector/power supply on the Stark Varg?

Not recommended. Overloading the pump line can kill the bike's power or trigger a check engine error. It's better to run the headlight from a separate power bank.

from the Stark Varg chat · separate page
How do I enable Telegram notifications about charging my bike in VargLink?

Telegram charging notifications are set up from your personal account. Instructions: https://varg.aupov.tech/help#telegram

from the Stark Varg chat · separate page
How does charging behave if you set an 80% limit at 1 kW power?

You can set 1 kW up to 80%. Once it reaches 80%, charging will stop and jump between 0 and 0.3 kW (balancing is in progress). After a full charge, balancing behaves differently: it may run for a whole day, or it may shut off after an hour. What it depends on is unknown.

from the Stark Varg chat · separate page
Do I need to manually start an activity on my Garmin watch when using VargLink?

No, the activity will start on its own if you tick the activity checkbox in the app.

from the Stark Varg chat · separate page
How do I record a Garmin workout if my watch is paired with one phone but I need to view the data on a second one?

The watch can only be paired with one phone. Garmin Connect sends data to the cloud rather than storing it locally. On the second phone, install Garmin Connect, don't pair the watch over Bluetooth, and sign in with the same account (same email and password). The workout data will show up there once the workout is finished.

from the Stark Varg chat · separate page
How can I see the real mileage of my Stark Varg if it was reset after an update and service?

The VargLink app will show the real mileage. You can get information about it from the bot @starkvarg_help_bot.

from the Stark Varg chat · separate page
Should you tell Stark Varg support about using third-party apps (e.g. VargPilot)?

It's not recommended. Support doesn't recognize uncertified third-party apps and may use that as grounds to refuse warranty coverage. One member was told exactly that: don't use third-party apps, we don't see any problems.

from the Stark Varg chat · separate page
Are there aftermarket alternatives to the protective glass for the Stark phone (Arkenstone, EX), or only the original?

Yes, there is an alternative: the screen protector for the Infinix Hot 40i (X6528B), 6.56", fits the Arkenstone. It's available on marketplaces.

It doesn't cover the whole screen, but overall it's fine.

from the Stark Varg chat · 07.11.2026 · separate page
Why is the yellow indicator lit on my bike when it's switched off?

One possible cause: the charger is connected to the bike but not plugged into the wall outlet.

from the Stark Varg chat · separate page
At which stage of the phone update can I stop worrying if the connection drops?

After the "transferring" stage and before "updating" it no longer matters: at this step the VCU is being updated.

from the Stark Varg chat · separate page
Can you quickly swap the battery on a Stark during a race, and do you need any firmware flashing?

The bike has holes for quick battery replacement. A fast mechanic can swap the battery in about 50 seconds. Warranty: if you put the stock battery back, the manufacturer won't know. It's easier to do the swap with the bike laid on its side, ideally on something raised so the battery is parallel to the ground. Nuts are welded to one side of the frame, and the plastics come off quickly.

from the Stark Varg chat · separate page
Can I set the charge limit of the Stark Varg remotely?

Yes, that's what VargLink was originally written for. There's also a Telegram miniApp.

from the Stark Varg chat · separate page
How can I get a notification when my Stark Varg finishes charging?

A Telegram bot sends you a message when charging is finished. It shows the final percentage and the gain over the charging time, for example: "charging finished — 81% (+70% in 8 h 58 min)".

from the Stark Varg chat · separate page
What is the top speed of the Stark Varg (MX, EX) and what are the stock sprockets? How do sprockets change top speed?

Stock sprockets and top speed

  • MX 1.2 — sprockets 14/47. The manual says 154 km/h, but on stock sprockets it's actually about 160–165 km/h.
  • EX — sprockets 12/48, shorter gearing for enduro. The manual says 129 km/h, in reality about 130–136 km/h.
  • First-generation MX — sprockets also 14/47. The manual says 110 km/h, but that figure is understated: in reality it's about 160–165 km/h (the motor spins up to 14,200 rpm, calculated ~165).
  • SM — sprockets 15/47, chain 520, 114 links. Top speed according to Stark — 154 km/h (96 mph). Tires 120/70-17 and 140/70-17 (rear about 628 mm). For the SM, figures are calculated proportionally from 154 at 15/47: 16/47 — about 164 km/h, 15/45 — about 161 km/h.

How sprockets change speed

Top speed is proportional to the front/rear ratio: new ≈ old × (new front/rear) ÷ (old front/rear). One more tooth on the front gives about +7% speed, one tooth less on the rear gives about +2%. You get less pull down low. This is theory: in reality load, wind, tire pressure all matter, and after a sprocket change the speedometer is off proportionally.

Calculation for MX and EX: the motor spins up to 13,900 rpm, the primary ratio is about 3.29, wheel circumference is about 2.14 m.

  • 14/47 — about 162 km/h
  • 14/48 — about 158 km/h
  • 13/47 — about 150 km/h
  • the first MX spins up to 14,200 rpm — about 2% faster on the same sprockets
  • EX on 12/48 — about 136 km/h, on 13/48 — about 147 km/h, on 14/47 — about 162 km/h, same as the MX
from the Stark Varg chat · 09.11.2026 · separate page
What should I do if my Stark pulls poorly uphill in a certain power mode?

Check whether traction control is turned on. You can turn it off in the VargLink app. The mode with maximum protection, i.e. the one with traction control, can get in the way of climbing hills. When you switch modes, the set values are shown at the bottom.

from the Stark Varg chat · separate page
Is it bad to charge the bike at higher power (2–3.3 kW) to charge faster?

It's not bad: you can safely charge at up to 3.3 kW, and the cells can handle even 7 kW. You just need to keep an eye on cell imbalance from time to time.

from the Stark Varg chat · separate page
How can I find out how long the bike will take to charge at a given charge percentage and charging power?

VargLink estimates the charging time fairly accurately. The info is shown under the charging circle and updates when you change the percentage or the power, so it works as a kind of calculator.

from the Stark Varg chat · separate page
How does the Stark Varg manage wireless charging of the phone on the handlebar: when does it turn on, and will the phone drain?

The bike manages wireless phone charging by itself.

When the bike is charging

  • Phone charging is always on.

At rest (not charging)

There are two modes, one after the other:

  • First, by 50/80 thresholds. The phone drains to 50%, charging switches on and brings it up to 80%. Drain at rest is about 7%/h (80→50 in 4 h 15 min), charging is about 17%/h (50→80 in 1 h 50 min).
  • Then, by timer: charging switches on for exactly 1 hour every 3 hours (for example at 04:24, 08:25, 12:27), without waiting for 50%. The charge level stays roughly between 57 and 81%.

Bottom line

The phone on the Stark won't die as long as the bike's battery is alive: at rest it gets topped up for 1 hour every 3 hours.

Observations from other owners (firmware 1.15)

  • On bikes 009643, 001798 and 013159 it's the same: first the 50/80 thresholds, then the "1 h every 3 h" timer.
  • On 009643, timer charging once reached 100%, so there is no 80% ceiling in this mode.
  • Drain at rest on these phones is 4–4.5%/h. On 2084 it's noticeably higher, about 7%/h.
from the Stark Varg chat · 10.11.2026 · separate page
How does wireless phone charging work on the Stark when the bike isn't plugged in and is idle (standby)?

The bike manages wireless charging by itself. First it works on 50/80 thresholds: the phone drains to 50%, charging kicks in and brings it up to 80%. Idle drain is about 7%/h, charging is about 17%/h. Then (on firmware 1.15; others report the same) it switches to a timer: charging turns on for 1 h every 3 h, without waiting for 50%, and the phone's charge stays roughly between 57 and 81%. On one bike the timer-based charging once went all the way to 100%, so there is no 80% cap in this mode. As long as the bike's battery is alive, your phone won't die.

from the Stark Varg chat · separate page
How does phone charging work on the Stark while the bike is plugged in to charge?

When the bike is plugged in and charging, the phone charging is always on.

from the Stark Varg chat · separate page
What is the part (rubber hose/tube) sticking out under the fender on the Stark, and does it need to be routed higher?

That's the motor breather. On the MX and EX it's located right there. If you don't ride through deep water crossings, there's no need to raise it higher; for deep water crossings, the advice is to raise it as high as possible, up under the tail plastic. The gearbox breather is a separate one.

from the Stark Varg chat · separate page
How do I remove the seat on the Stark EX and MX?

The seat comes off the same way on the MX and EX: first remove the plastic as an assembly (the spoiler), then unbolt the seat itself.

What to unbolt (according to owners):

  • at the front, two bolts on each side, where a KTM has its radiator shrouds
  • on the sides, one big bolt each, where the "boots" are
  • under the rear fender, the fasteners (on the MX there is one central bolt; on the EX there are about 5, plus extra plastic, including the number plate holder)

Stark videos (no voiceover; check the manual for torque specs):

from the Stark Varg chat · 11.11.2026 · separate page
Where can I buy a charger for the Stark Varg?

Chargers are available from @BackJumpMoto, and @bazarspbendurosales may have them too. Check prices and availability with them directly.

You can also ask Dima (@WRracer) or Kirill (@Kir_B97) at StarkShop — they should have their own price list.

Official Stark store (prices on the website differ from the prices quoted in the chat):

  • portable charger — $799, reportedly on sale from May 2026; with an adapter (not included) it can be plugged into a car AC charger;
  • stand charger — $1149;
  • Varg charging cable — $114.99.

This information about the official store comes from the internet and has not been confirmed in the chat.

from the Stark Varg chat · 11.11.2026 · separate page
How do the Stark's brakes change when you mount the front caliper on the rear?

A rider who compared a Stark with the front caliper on the rear against one with the stock caliper said the difference is huge: with the stock caliper it feels like there are no brakes at all.

from the Stark Varg chat · separate page
How does the Stark behave in terms of battery consumption in hard enduro and in cross-country?

According to riders, battery consumption is low in hard enduro and in rocky creek beds, but the battery drains quickly in cross-country and on fast runs. You have to conserve charge and hold back on the throttle, which costs you time. One rider thinks that adding 1–2 kWh of battery would solve almost all the problems. Another reported that an improved battery is coming soon.

from the Stark Varg chat · separate page
What should I do if the Starkphone stopped charging on the bike's built-in wireless charger, even though other phones charge fine?

Check and clean the charging connector: for the author, cleaning used to fix it. Try a different wireless charger – you have to find the exact sweet spot on it, otherwise it only charges for a few seconds. The fault can also appear after a hit or a crash of the bike. Denis Ayupov had his charger replaced under warranty.

from the Stark Varg chat · separate page
The battery only charges to 98–99% when charging to 100%, or it bounces between 99 and 100%. What does this mean and what should I check?

This is a sign of an unbalanced battery: if it only charges to 98 or 99% when the charge is set to 100%, or it bounces between 99 and 100%, the cells need balancing. It's possible that balancing is actually in progress right now.

What to check: install the latest version of VarGlink. While charging, it shows the cell imbalance and the moments when it grows or shrinks.

from the Stark Varg chat · 16.11.2026 · separate page
What should I do if the firmware update from my phone gets to about 50%, then the bike shuts off / Wi‑Fi disappears and the update fails (bike version 1.2.0)?

If the update via phone doesn't go through, there's only one option left: updating via the bike's modem (VCU board). You need to write in saying you want to update, and they'll send you a replacement modem. You swap it in, send them yours, and the bike gets updated. The replacement modem has to be returned (the terms are clarified in a private message).

from the Stark Varg chat · separate page
How can I get the (brake) levers to sit closer to the grip?

Fit 2 springs on each lever: each lever then sits closer to the grip, and the brake feels very comfortable.

from the Stark Varg chat · separate page
How is battery charging organized at the Enduro Four Seasons race, and how much can you charge?

There's a mandatory one-hour charging stop in the middle of the track. You hand your chargers over to the organizers, like jerry cans, and an industrial generator powers them. Not at full power, about 30% was charged in an hour. Denis estimated the maximum at 3 kW, which is around 40%. When everyone switched on at full power, the generator's kettle tripped off.

from the Stark Varg chat · separate page
Where can I see the temperatures of individual battery sensors and the number of the hot sensor?

In VargLink: "battery ›" under the ring, where the per-sensor temperatures are shown. The number of the hot sensor is not sent to the server. To get to the bottom of it, the owner can take a photo of this screen at the moment of the warning or send feedback with a log from the app.

from the Stark Varg chat · separate page
My Stark Varg shows a red indicator while riding and stops driving, then after waiting and a restart it runs again. What should I check?

Tips: check the pump, bleed the coolant (there's a video on YouTube), and check the throttle grip contacts. These symptoms can also show up when the battery, motor or inverter is dying.

from the Stark Varg chat · separate page
What can I use to check errors/diagnostics on the Stark Varg?

Owners recommend installing VargLink (varg.aupov.tech) and checking in it.

from the Stark Varg chat · separate page
Can I adjust the power curve in the app?

No, the developer didn't build that feature.

from the Stark Varg chat · separate page
What's the status of the Amazfit (Zepp) watch app, and how can I test it?

The Zepp submission hasn't been approved yet; they're dragging their feet (Garmin processes things faster). To test it, you can get a QR code from the developer, and you need to enable developer mode on the watch. The watch will show the battery charge. The app works both on its own and alongside the stock one.

from the Stark Varg chat · separate page
The motor and inverter show about 182–183 °C on a cold, parked bike and power is being cut. What is this and what should I check?

Most likely the temperature sensors (or their circuit) are lying, not a real overheat: ~183 °C is the top of the scale, and that is what a shorted sensor or circuit looks like. The bike believes these numbers: it limits power (alert 0x8000), runs the fan and pump, and the inverter shows code 0x4300.

What to do:

  1. In VargLink open "Diagnostics" → "Motor and inverter" and look at the three motor values and the three IGBT values.
  2. If only one sensor reads 183 °C, that sensor or its wire is faulty. If all three in a group read it, the problem is a common circuit (the motor–inverter signal connector or the measurement board in the inverter).
  3. Check "Inverter humidity" (above 55–70 % means water).
  4. Ask whether the bike was washed or ridden through water.
  5. Inspect and dry the motor–inverter signal connector.
  6. Switch the bike fully off for about 30 seconds, then switch it on again.

If the values still show ~183 °C on a cold bike, take it to a dealer (sensor or inverter). Riding it is not recommended.

from the Stark Varg chat · separate page
Can the bike be set up so it doesn't roll backwards on a hill when I close the throttle?

You can't set it up that way: on any climb with the throttle closed, the bike will roll. The throttle works like a brake, and the brakes are on the handlebars, so you have to get used to it. Don't close the throttle completely when you're stopped on a slope. If you start rolling backwards, let it roll back a little and then gas it uphill.

from the Stark Varg chat · separate page
What should I do if my bike breaks down while it's still under warranty and I have third-party apps installed?

Contact support and let them run the diagnostics themselves. Don't show them the third-party apps, leave everything stock and tell them the bike shuts off.

from the Stark Varg chat · separate page
How can I practice to get more confident controlling the bike on climbs and descents?

Do simple drills slowly on the throttle: up and down hills in reverse, without using the brakes. Ideally, also ride with the front wheel up – that helps too.

from the Stark Varg chat · separate page
What should I do if the app won't connect to the bike (already on version 3.5.0)?

Update the app to 3.5.0. If that doesn't help, restart the bike, restart your phone and try again. A possible cause is that the app can't connect to the bike's Wi-Fi.

from the Stark Varg chat · separate page
Where can I check my Stark's status (battery, errors) in the VargLink app, and where is the help for it?

The app website: varg.aupov.tech. Help: varg.aupov.tech/help and varg.aupov.tech/faq. You can also ask the bot @starkvarg_help_bot.

from the Stark Varg chat · separate page
Why fit a spring in the brake lever and what does it do?

The brake lever sits closer to the grip, and the extra free play (the lever flopping around) goes away. To fit the springs, remove the lever and reassemble it with the spring. If you keep a finger on the lever, you may not need them.

from the Stark Varg chat · separate page
Can I swap the front and rear brake levers?

It's not a good idea: the rear brake and the throttle should be on different hands, otherwise you could accidentally pull the rear brake while giving it gas. You'd also have to change the hydraulic lines.

from the Stark Varg chat · separate page
The handlebar remote works intermittently (sometimes it works, sometimes it doesn't) — what should I check?

Inspect the remote's wiring: take it out of the handlebar and check it visually, wiggle it while the remote is powered on and connected, and if possible test it for continuity. Also check the wiring from the phone charger to the connector under the frame: on another bike a similar fault (it only worked when the handlebar was turned) was caused by that. If that doesn't help, contact support: the remote may be replaced under warranty.

from the Stark Varg chat · separate page
How do I share a track or ride a ready-made track in VargLink?

You can send a track to other people. You can upload it in your bike's personal account and then ride along it. On a group ride, you can turn on the ride track.

from the Stark Varg chat · separate page
Can I store a Stark VARG EX at sub-zero temperatures (for example, −5 °C), and when can I charge the battery?

Storing the bike at −5 °C is outside the allowed conditions and can shorten battery life. Keep the bike in a dry room above 0 °C, and don't charge it until the battery temperature has risen above 4 °C. If you're riding in the cold, it's best to head out straight from a warm bike, so the battery cools down less.

from the Stark Varg chat · separate page
Where can I buy protective glass for the Stark VARG EX?

@Kir_B97 should have the original glass.

from the Stark Varg chat · separate page
Can a Stark Varg run normally if some cell parallels (parallel groups) in the battery have dropped out?

One member has seen bikes with three dropped parallels, and they ran fine. How long they will keep running like that is unknown. Such batteries have turned up on both firmware 1.2.0 and the latest 1.15.

from the Stark Varg chat · separate page
What do the statistics on dead cells in Stark Varg batteries show, and which cell shows up most often?

In the statistics collected from the site (not all owners share their data), there were 6 bikes with dead cells: 3 had one dead cell each, and 3 had three each (three being the maximum). Cell #57 appears in 4 of those 6 bikes. There's no data on owners who don't share their statistics.

from the Stark Varg chat · separate page
What charge level should I keep the Stark VARG battery at for winter storage?

80% is too high for storage. Stark's own storage charge is 60%, and 30–50% is considered the safest. If there is no cell imbalance, you don't have to discharge it down to 30%.

from the Stark Varg chat · separate page
How do I lower the battery charge before winter storage if I can't ride?

Leave the bike in sleep mode (standby) with no phone connected. Self-discharge is about 2% per day, so going from 80% down to the level you need takes roughly 15 days.

from the Stark Varg chat · separate page
Do I need an internet connection to pair my phone with the bike in VargLink?

No, internet doesn't matter for connecting the phone to the bike.

from the Stark Varg chat · separate page
What is the Stark portable charger called in the app?

Backpack Charger Stark — that's what Stark itself calls it, too.

from the Stark Varg chat · separate page
Where can I change the LED brightness on the mode switch?

There's a setting for it in the menu — the LED brightness can be adjusted in the settings.

from the Stark Varg chat · separate page
Should I charge my Stark to 100% or 80% to be safer for the battery?

You can charge to 100% and not worry about it. The main thing is not to store the battery fully charged at 100%. If you ride often, charge to 100%. If you ride rarely, charge to 80% and top it up before riding.

from the Stark Varg chat · separate page
Can I charge a Stark with a 1 kW charger?

Yes, a 1 kW charger is fine.

from the Stark Varg chat · separate page
What is the latest version of the Stark Varg EX app?

The latest app version is 3.5.0.

from the Stark Varg chat · separate page
When inspecting a used bike, the diagnostics show a norm of 0.01 and an imbalance of 18. Is that critical?

No, it's nothing. The norm of 0.01 is given in volts: 0.01 V = 10 mV, so the imbalance of 18 is measured in millivolts. It's also recommended to check the readings of all the temperature sensors.

from the Stark Varg chat · separate page
At what cell imbalance does the Stark stop balancing the battery?

When the cell imbalance drops below 10 mV.

from the Stark Varg chat · separate page
How should I run battery balancing so that a memory effect doesn't appear?

The best approach is to start balancing each time at around 80% (±) state of charge, and to vary the value from one time to the next so the memory effect doesn't kick in.

from the Stark Varg chat · separate page
How do I check the battery after balancing if the cells look fine at rest?

Cells can look fine at rest, so you need to ride under normal load and see which cells sag after the ride. If you keep running the bike with such a cell, you can lose it.

from the Stark Varg chat · separate page
Didn't find an answer? Ask the bot @starkvarg_help_bot or the Stark Varg chat (in Russian).